跳到主要内容

挤出机参考相关

本页面收录常见挤出机的参考参数，主要用于快速建立初始配置。

使用说明
  • 下方 rotation_distance、gear_ratio、pressure_advance 仅供参考，实际机器需要重新校准。
  • 更换挤出机、电机、齿轮、耗材路径或喷嘴后，都建议重新校准挤出步进值。
  • pressure_advance 与热端、耗材、速度和切片参数有关，不能直接照抄。

参考配置​

Stealthburner-Clockwork2​

rotation_distance: 21.84
gear_ratio: 50:10
microsteps: 16

Voron-Afterburner-Clockwork​

rotation_distance: 21.84
gear_ratio: 50:17
microsteps: 16

Galileo2​

rotation_distance: 47.088
gear_ratio: 9:1
microsteps: 16

BMG && BMG Wind​

rotation_distance: 25.1200
gear_ratio: 50:17
microsteps: 16
full_steps_per_rotation: 200

Nf sunrise​

microsteps: 16
rotation_distance: 4.46
max_extrude_only_distance: 120.0
max_extrude_only_velocity: 80.0
max_extrude_only_accel: 800.0

Orbiter 2 && Orbiter 2.5​

microsteps: 32
full_steps_per_rotation: 200
rotation_distance: 4.637
nozzle_diameter: x.xx
filament_diameter: 1.750
max_extrude_only_distance: 500
max_extrude_only_velocity: 120
pressure_advance: 0.025
pressure_advance_smooth_time: 0.03

LDO Smart Orbiter 3.0​

microsteps: 16
full_steps_per_rotation: 200
rotation_distance: 4.69
max_extrude_only_distance: 500
max_extrude_only_velocity: 120
pressure_advance: 0.015
pressure_advance_smooth_time: 0.03
max_extrude_cross_section: 10

Hextrudort Low && Hextrudort Low PLUS​

Standard version​

rotation_distance: 22
# gear_ratio: 50:10 # 标准 10T 电机
gear_ratio: 50:8    # 标准 8T 电机
pressure_advance: 0.025
pressure_advance_smooth_time: 0.03

PLUS version​

rotation_distance: 35.8
# gear_ratio: 60:10 # 标准 10T 电机
gear_ratio: 60:8    # 标准 8T 电机
pressure_advance: 0.025
pressure_advance_smooth_time: 0.03

Sherpa MINI​

gear_ratio: 5:1
microsteps: 16
rotation_distance: 22.388
max_extrude_only_distance: 100.0
max_extrude_cross_section: 50.0

MK8​

microsteps: 16
rotation_distance: 34.406
max_extrude_only_distance: 100.0

玄武热端参考配置​

[extruder]
## In M1 position
### Vz-HextrudORT
step_pin: SHT36:gpio7
dir_pin: !SHT36:gpio6
enable_pin: !SHT36:gpio14
full_steps_per_rotation: 200
rotation_distance: 23.24
gear_ratio: 30:10
microsteps: 16
nozzle_diameter: 0.6
filament_diameter: 1.750
heater_pin: SHT36:gpio23
sensor_type: PT1000
sensor_pin: SHT36:gpio27
control: watermark
min_temp: 0
max_temp: 400
max_extrude_only_distance: 1000.0
max_extrude_cross_section: 500
max_extrude_only_velocity: 200
max_extrude_only_accel: 10000
min_extrude_temp: 0
pressure_advance: 0.04
pressure_advance_smooth_time: 0.03

双加热口控制一个热端​

如果使用两个加热口共同控制加热棒，可使用 [multi_pin] 合并加热引脚，然后将 heater_pin 改为 multi_pin:extrude_heater。

printer.cfg
[multi_pin extrude_heater]
pins: PA1,PA2

[extruder]
heater_pin: multi_pin:extrude_heater
Loading...