Skip to main content

USB Firmware Compilation

Connecting to the Host Computer​

Core Connection Limitation

The Fly-DP5 mainboard can only communicate with the host computer for Klipper via the Type-C USB interface.

Loading...

Brief Guide to Firmware Compilation​

Notes​

  • Network: Ensure the host (Raspberry Pi, etc.) is connected to the internet.
  • Login Method: Must log in via SSH over the network; serial port access is disabled.
  • Input Method: Keep the keyboard in English half-width mode.

SSH Login and User Switching​

Use tools like MobaXterm, PuTTY, etc., to SSH into the host.

Switch User:​

  • Standard System (Official Raspberry Pi system, etc.)
    Do not use root; switch to a regular user: 
    su <username>
  • FLY Host System (FlyOS-FAST system)
    Only supports login as root user (password: mellow)

Firmware Compilation Operation Guide​

In the Klipper firmware configuration interface, only keyboard operations are supported; the mouse cannot be used.

KeyFunction
↑ / ↓Move cursor up/down to select menu items
Enter / SpaceConfirm selection, check options, or enter submenus
ESCReturn to the previous menu
QExit the configuration interface
YIf prompted when exiting, press Y to save the configuration

Start Firmware Compilation​

The following describes how to compile the firmware:

  • After connecting via SSH, enter the following command and press Enter:

    cd ~/klipper && rm -rf ~/klipper/.config && rm -rf ~/klipper/out && make menuconfig

  • Among them, rm -rf ~/klipper/.config && rm -rf ~/klipper/out deletes the previous compilation data and firmware.

  • make menuconfig compiles the firmware. After execution, the following interface should appear.

    Loading...

  • Select Enable extra low-level configuration options and press Enter.

    Loading...

  • Enter the menu Micro-controller Architecture and select STMicroelectronics STM32, then press Enter.

    Loading...

  • Enter the menu Processor model, select STM32F072, and press Enter.

    Loading...

  • Select Bootloader offset, choose: 8KiB bootloader

    Loading...

  • For Communication interface, select: USB (on PA11/PA12) and press Enter.

    Loading...

  • Please verify against the image below to ensure it matches before proceeding to the next step.

    Loading...
  • Press the Q key, when Save configuration appears, press the Y key.
    Loading...
  • The configuration should now be saved, and you should be back at the command line interface.
  • Enter the following command to start compilation. This will take a while.
make -j4
Loading...
  • Compilation is successful if the following output appears at the end.
  • Due to Klipper version differences, the appearance of out/klipper.bin alone indicates success. 
    Linking out/klipper.elf
    Creating bin file out/klipper.bin

Entering Flash Mode​

  • After connecting the mainboard to the host computer using a Type-C data cable, double-click the RST button. At this point, the LED on the mainboard will blink.
Loading...

Flashing Firmware​

Starting the Flashing Process​

  • Non-Fly official upper computers require Katapult installation
  • Install Katapult

Obtaining the Mainboard ID​

Execute the following command to search for the device ID. Under normal circumstances, an ID similar to the image below should be displayed (Note: Each mainboard has a different ID):

ls /dev/serial/by-id/*

If the searched ID contains usb-katapult_stm32xxxxxxxx, you can proceed to the next step

Loading...

Flashing the Firmware​

⚠️ Preparation
  • Ensure the firmware file has been compiled
  • Replace <your_mainboard_ID> in the command below with the actual ID obtained in the previous step
  • For standard upper computers, use the following code 
    ~/klippy-env/bin/python ~/katapult/scripts/flashtool.py -d <your_mainboard_ID>
  • For FLY upper computers, use the following code 
    python3 ~/katapult/scripts/flashtool.py -d <your_mainboard_ID>

Flashing Process Reference:

Loading...

Flashing Success Reference:

Loading...

Firmware Update​

USB Firmware Update Steps​

  1. Query the Mainboard ID
ls /dev/serial/by-id/*
Identification Points

/dev/serial/by-id/usb-katapult_rp2040_E662549553642032-if00 in the image below is the mainboard ID

Loading...
  1. Update the Firmware
cd ~/klipper/ && make flash FLASH_DEVICE=<your_mainboard_ID>
Note
  • Replace <your_mainboard_ID> with the actual queried ID
Loading...

Solutions for Flashing the Wrong Firmware​

Method One: Quickly Enter Flash Mode​

  1. Power off the mainboard
  2. After powering back on, quickly double-click the RESET button
  3. Re-enter flash mode

Method Two: Re-flash the Katapult Firmware​

Click to View Katapult Firmware Flashing Guide

Searching for USB ID After Flashing​

After the firmware flashing is complete and the mainboard has been powered on again, please proceed to search for the USB ID.

View USB ID Retrieval Method

Loading...