Introduction

1. Product Introduction

The FLY SB2040 PRO V3 is a tool board developed by Guangzhou Magnesium Wheel Electronics Technology Co., Ltd. specifically for the VORON Stealthburner print head. Using this tool board, four wires can replace the complex wiring originally required between the mainboard and the print head, optimizing the layout. The SB2040 is compatible with stealthburner and afterburner. It is a tool board that integrates a CAN transceiver, RS232 transceiver, USB port, TMC2240 driver, LIS2DW accelerometer sensor, three controllable fans, and other functions. This tool board is suitable for Klipper and RRF firmware.

1.1 Product Features

• Reserved Boot button, allowing users to enter Boot mode via Type-C to update firmware.
• Supports Klipper firmware and RRF firmware.
• Supports CAN mode, RS232 mode, and RRF CAN mode.
• In RS232 mode, it offers higher transmission rates and stronger stability. In CAN mode, it supports CAN expansion with a reserved CAN expansion interface.
• Temperature sensor support: Onboard MAX31865 chip, compatible with PT100 and PT1000 temperature sensors.
• Onboard LIS2DW accelerometer sensor and LDC1612 sensor.
• Reserved RGB interface, onboard 2240 driver, supports various leveling sensors such as klicky, Voron Tap, PL08n, etc.
• Supports 12-24V voltage, 15A current input. Enlarged heater cartridge port with a rated current of 10A.

1.2 New Features

• Supports switching between Klipper CAN mode, RS232 mode, and RRF CAN mode.
• Added RS232 mode, offering higher transmission rates, stronger stability, and simpler debugging.
• Added RRF CAN mode, allowing switching to an RRF tool board, enhancing applicability.
• Added CAN expansion interface for easy connection of CAN devices.
• Added termination resistor DIP switch. The 120R termination resistor can be selected via the DIP switch, eliminating the need for jumpers.
• Added 1-meter power/signal cable. The cable uses a twisted-pair design for stronger anti-interference performance.

1.3 Product Specifications

• MCU: Raspberry Pi RP2040, Dual-core ARM Cortex-M0+ @133MHz
• Connection interface uses XT30 (2+2) connector supporting 15A current, 30A peak.
• Firmware: Reprap / Klipper
• Input Voltage: DC 12V-24V
• Logic Voltage: DC 3.3V
• Onboard Sensors: LIS2DW and optional LDC1612 and MAX31865
• Heater Cartridge Interface: Heater (HEAT0)
• Expansion Interfaces: RGB, EndStop, PT100/PT1000, XH2.54-2P CAN port
• Fan Interfaces: One DC fan, two DC fans or PWM fans
• Motor Driver: Onboard TMC2240
• Temperature Sensors: One 100K NTC or PT1000 (TH0), one optional PT100/PT1000

4. Product Classification

RRF Tutorial Link: RRF

SB2040	V3	Plus V3	Max V3	Pro V3	Pro Plus V3	Pro Max V3
Drive
Klipper CANBus	✅	✅	✅	✅	✅	✅
Klipper RS232	✅	✅	✅	✅	✅	✅
RRF CANBus	❌	❌	✅	❌	❌	✅
LIS2DW	✅	✅	✅	✅	✅	✅
MAX31865	❌	✅	✅	❌	✅	✅
LDC1612	❌	❌	✅	❌	❌	✅

Product Notes

Output Port	Max Current at 24V Power	Max Current at 12V Power
Heater Port	5A	2.5A
Fan Port	1A	0.5A